2010MayJun XC log - Revision history

192.153.157.220 at 02:39, 11 June 2010

2010-06-11T02:39:53Z

← Older revision		Revision as of 02:39, 11 June 2010
Line 27:		Line 27:

	not yet:		not yet:

	1. just start working on the new gui for real time flux,vis and CP.		1. just start working on the new gui for real time flux,vis and CP.

	2. a new button for sending offset to ople		2. a new button for sending offset to ople

192.153.157.220 at 02:39, 11 June 2010

2010-06-11T02:39:33Z

← Older revision		Revision as of 02:39, 11 June 2010
Line 1:		Line 1:
	done:		done:

	1. New 4-beam fiber explorer gui with photometric channels(PC)		1. New 4-beam fiber explorer gui with photometric channels(PC)
	On detector control tab, one can change PC position on detector.		On detector control tab, one can change PC position on detector.

192.153.157.220 at 02:39, 11 June 2010

2010-06-11T02:39:05Z

← Older revision		Revision as of 02:39, 11 June 2010
Line 1:		Line 1:
	done:		done:
	1. New 4-beam fiber explorer gui with photometric channels(PC)		1. New 4-beam fiber explorer gui with photometric channels(PC)
	On detector control tab, one can change PC position on detector. Normally one don't need to change the numbers unless PC are realigned.		On detector control tab, one can change PC position on detector.
	On fiber mapping tab, one can use the new function (perform map (xchan)) to do fiber exploring for all four together. In case the S/N is too low, one may switch back to old function (perform map), which does fiber exploring one at a time.		Normally one don't need to change the numbers unless PC are realigned.
			On fiber mapping tab, one can use the new function (perform map (xchan))
			to do fiber exploring for all four together. In case the S/N is too low,
			one may switch back to old function (perform map), which does fiber
			exploring one at a time.


	2. fixed home function for fiber stages.		2. fixed home function for fiber stages.
	Now if there is a power outage, what one has to do is: first clicked 'home all and index'; second click 'recall last positions'. You should be able to see some lights on the GUI, then do a detailed fiber explorer and may need to change z position a little if the focus is not good.		Now if there is a power outage, what one has to do is: first
	If after the two clicks, you still don't see lights, then maybe a new fiber stage's home trigger is broken. Right now these stages have broken home trigger: 1x, 1z, 2x, 4x, 4y(from the gui). You can check this by click 'home all' button, if the position number doesn't go to 0, the corresponding fiber stage has a broken home trigger. If you find a new x or y stage is broken, then just do a wide fiber explorer to find light. If it is z stage (you are in trouble!), you need to search z position step by step. My suggestion is to make the z step 100micron, and search xy range 400*400micro with 20 micron step from the middle (x=64000, y=64000)		clicked 'home all and index'; second click 'recall last positions'.
			You should be able to see some lights on the GUI, then do a detailed
			fiber explorer and may need to change z position a little if the focus
			is not good.
			If after the two clicks, you still don't see lights, then maybe a new
			fiber stage's home trigger is broken. Right now these stages have broken
			home trigger: 1x, 1z, 2x, 4x, 4y(from the gui). You can check this by click
			'home all' button, if the position number doesn't go to 0, the corresponding
			fiber stage has a broken home trigger. If you find a new x or y stage is
			broken, then just do a wide fiber explorer to find light. If it is z stage
			(you are in trouble!), you need to search z position step by step. My
			suggestion is to make the z step 100micron, and search xy range 400*400micro
			with 20 micron step from the middle (x=64000, y=64000)

	not yet:		not yet:
	1. just start working on the new gui for real time flux,vis and CP.		1. just start working on the new gui for real time flux,vis and CP.
	2. a new button for sending offset to ople		2. a new button for sending offset to ople

192.153.157.220: New page: done: 1. New 4-beam fiber explorer gui with photometric channels(PC) On detector control tab, one can change PC position on detector. Normally one don't need to change the numbers unles...

2010-06-11T02:36:23Z

New page: done: 1. New 4-beam fiber explorer gui with photometric channels(PC) On detector control tab, one can change PC position on detector. Normally one don't need to change the numbers unles...

New page

done:
1. New 4-beam fiber explorer gui with photometric channels(PC)
On detector control tab, one can change PC position on detector. Normally one don't need to change the numbers unless PC are realigned.
On fiber mapping tab, one can use the new function (perform map (xchan)) to do fiber exploring for all four together. In case the S/N is too low, one may switch back to old function (perform map), which does fiber exploring one at a time.

2. fixed home function for fiber stages.
Now if there is a power outage, what one has to do is: first clicked 'home all and index'; second click 'recall last positions'. You should be able to see some lights on the GUI, then do a detailed fiber explorer and may need to change z position a little if the focus is not good.
If after the two clicks, you still don't see lights, then maybe a new fiber stage's home trigger is broken. Right now these stages have broken home trigger: 1x, 1z, 2x, 4x, 4y(from the gui). You can check this by click 'home all' button, if the position number doesn't go to 0, the corresponding fiber stage has a broken home trigger. If you find a new x or y stage is broken, then just do a wide fiber explorer to find light. If it is z stage (you are in trouble!), you need to search z position step by step. My suggestion is to make the z step 100micron, and search xy range 400*400micro with 20 micron step from the middle (x=64000, y=64000)

not yet:
1. just start working on the new gui for real time flux,vis and CP.
2. a new button for sending offset to ople