2010-06-14 ========== Program: CL2 (YSOs, PI: Millan-Gabet et al.) Observers: Stefan Kraus, Fabien Baron Telescope: S1-S2-W2-E2 Beams: B5-B5-B6-B6 POPs: 4- 1- 1- 5 Baselines (at hour angle 0): S1S2: 30m, 170deg S1W2: 189m, 160deg S1E2: 246m, 17deg S2W2: 159m, 157deg S2E2: 220m, 20deg W2E2: 152m, 67deg CLASSIC on beam 5&6 Possible Baselines: S1-E2 S1-W2 S2-W2 S2-E2 LT 20:52 = UT 03:52 = LST 13:30 LT 20:52 *** BASELINE S1W2 (190m) LT 20:52 - Del Sco, for fringe finding alignment, some repairs in the lab LT 21:35 scanning for fringes recording data NORM 500Hz, seeing 4-5cm recording data NORM 1000Hz (200 Hz Frg), offset -0.45cm LT 21:50 - HD143900 calibrator (K=3.1) recording data NORM 1000Hz LT 22:00 - Del Sco recording data NORM 1000Hz LT 22:05 - HD143900 calibrator recording data NORM 1000Hz LT 22:12 - Del Sco problem with fringe search (delay lines do not move) recording data NORM 1000Hz, offset -0.05cm FLUOR did a clock sync (data looked strange on screen, maybe problem?) LT 22:30 - HD143900 calibrator recording data NORM 1000Hz optimizing alignment again, seeing 6-7cm LT 22:40 - HD150366 (K=5.5, V=6.0) calib for MWC863 recording data NORM 500Hz, offset -0.28cm, seeing 3-5cm recording data SYNC 500Hz, offset -0.19cm to -0.15cm LT 23:03 - HD142666, seeing 6-8cm LT 23:35 found no fringe, give up LT 23:38 - HD150366 found fringe at +0.135cm LT 23:45 - MWC863. seeing 4-11cm recording data NORM 500Hz, offset +0.19cm to +0.26cm (SYNC saturates) LT 23:59 - HD150366 recording data NORM 500Hz, offset +0.24cm LT 00:06 - calibrator ??? (HD buttom was not pressed, so this was not HD188385, instead it was an earlier calibrator around RA=16h, either HD150366 or HD143900) record NORM 500Hz, offset +0.47cm to +0.49cm LT 00:25 - V1295Aql star does not show up in W2 only 60 counts LT 00:48 HD190327 doing pupil on bright star LT 01:00 - HD188385, seeing 4-9cm recording NORM 500Hz, offset -0.16cm, interrupted since we can do SYNC mode recording SYNC 500Hz, offset -0.15cm to -0.08cm, 100 counts LT 01:10 - V1295Aql recording SYNC 500Hz, clear fringe, 100 counts offset -0.11cm, -0.085cm (01:22), -0.046cm (01:27), -0.020cm (01:29) LT 01:30 - HD188385, seeing 4-7cm recording SYNC 500Hz, offset +0.139cm (01:37), +0.20cm (01:44), 80-100 counts LT 01:45 - V1295Aql, seeing 4-5cm recording SYNC 500Hz, offset +0.24cm, +0.28cm (02:05), +0.31cm (02:08) LT 02:08 - HD188385 recording SYNC 500Hz, offset +0.32cm (02:14), +0.347 (02:19) LT 02:22 *** BASELINE S1E2 (246m, S1 reference) LT 02:30 Tau Aql NIRO alignment scan for fringe, found at offset +0.22cm LT 02:40 - HD188385 recording SYNC 500Hz, offset +0.22cm (02:39), +0.24 (02:45) counts 100-140 LT 02:45 - V1295Aql recording SYNC 500Hz, offset +0.24cm (02:53), +0.275 (03:05), +0.292 (03:08), counts 140 LT 03:09 - HD188385, seeing 6-9cm recording SYNC 500Hz, offset +0.33cm (03:10), +0.34cm (03:15) LT 03:17 - HD187897 (check calibrator) recording SYNC 500Hz, offset +0.38cm (03:21) in some individual frames slightly saturated, record nevertheless, maybe cutoff upper 10-15% in data reduction LT 03:27 - V1297Aql, seeing 5-9cm cannot find fringes, go back to calibrator LT 03:40 - HD188385 cannot find fringes opel is not running, fix it find fringes again recording SYNC 500Hz, offset +0.54cm (04:02), +0.56cm (04:09) LT 04:09 - V1295Aql recording SYNC 500Hz, offset +0.58 (04:18), +0.59 (04:22), +0.615 (04:27), +0.625 (04:30) fringe very difficult to see, but sure it is there, counts 120-130 LT 04:30 - Tau Aql optimizing alignment again LT 04:35 - HD189509 (check calibrator) recording SYNC 500Hz, offset +0.666 (04:37), +0.68 (04:40), +0.693 (04:43) LT 04:44 - V1295 Aql, seeing 7-8cm recording SYNC 500Hz, offset +0.69 (04:45), clear fringe, counts 150 maybe saturating in some scans (check for data reduction) LT 04:55 - HD188385, seeing 5-8cm recording SYNC 500Hz, offset +0.87 (05:09) LT 05:15 closing down