UT 2010-Jul-22
==============
Program CL3, PI Kraus

Observers: Fabien, PJ

CHARA/CLIMB
TEL       E1-S1
POP       1  1 
BEAM      B5-B6
REF CART  S1

Starting
LT 21 July 2010, 20:30 
Weather: clear
r0 = 6-10 cm

Bad start, E1 cart is stuck...
Rehoming as the carts were lost (E1 was at the back)


Attempting v1295aql
align niro on HD188385
21:10 switching to cal HD188385
21:20 recording fringes at 250Hz/DEST/LONG (too low counts in 500Hz)
      3404
      Vis:0.50
      Sum:90
21:39 3300
      switching to v1295aql
21:43 recording fringes at 250Hz/DEST/LONG
      3283
      Vis:0.13
      Sum:100
21:58 3190
      switching to cal 189509
22:00 recordign fringes at 250Hz/DEST/LONG
      3257
      Vis:0.48
      Sum:70
22:12 3200
      switching to v1295aql
      recording fringes at 250Hz/DEST/LONG
      3030
      Vis:0.13
      Sum:80      
22:25 3050
22:31 3020
      switching to HD188385
      recording fringes at 250Hz/DEST/LONG
      Vis:0.38
      Sum:65
22:46 2990
      switching to v1295aql
piston getting worse
      recording fringes at 250Hz/DEST/LONG
      Vis:0.12
      Sum:100
23:14 switching to 189509
      recording fringes at 250Hz/DEST/LONG
      ran out of delay after the first shutter sequence
      so took a *very* short number of fringes

Attempting MWC340 and MWC342
niro align on cal 194708

23:33 scanning for offset on hd194708
      found 4220
      recording fringes at 250Hz/DEST/LONG (t/t NUM=1)
      Vis:0.45
      Sum:140
23:48 4258
      putting NSUM to 5 from now on
0:00 switching MWC340
     recording fringes at 250Hz/DEST/LONG (t/t NUM=5)
     Vis:0.16
     Sum:180
0:10 4144
     switching again to HD194708 but with NUM=5
0:17 recording fringes at 250Hz/DEST/LONG 
     Vis:0.40
     Sum:200
0:30 switching to MWC340
0:32 recording at 250Hz/DEST/LONG
     4233
     Vis:0.12
     Sum:150
0:45 4290
     switching to calibrator 195988
0:49 recording fringes at 250Hz/DEST/LONG
     4438
     Vis:0.42
     Sum:160
1:01 4390
     switching to MWC340
1:04 recording fringes on MWC340 at 250Hz/DEST/LONG
     fringes seem much fainter, piston much worse
     Vis:0.08
     Sum:120
1:11 4320
1:22 4279
     switching to calibrator 194708
1:28 recording fringes on 194708 at 250 Hz/DEST/LONG
     4396
     Vis:0.37
     Sum:150
1:40 4360
     switching to MWC340
1:45 recording fringes at 250Hz/DEST/LONG
     fringes look stronger than in the previous set
     Vis:0.11
     Sum:140      
1:58 4142
     switching to 195988
1:59 recording fringes at 250Hz/DEST/LONG
     4340
     Vis:0.44
     Sum:130
     
Attempting MWC342
NIRO align on target
switching to calibrator HD191610
NSUM at 5 for all the MWC342 fringes
2:21 scanning for offset - found at 3854
2:23 recording fringes at 500Hz/DEST/LONG
     Vis:0.56
     Sum:130
2:28 3961
2:31 switching to MWC342
cannot find fringes
check on other cal, found fringes at 4079
switched back to target, still cannot find fringes
probably at null ?

Attempting WR140
3:00 niro align on WR140
switching to calibrator HD192985
3:05 scanning for offset - found 3909
     recording fringes at 500Hz/DEST/LONG
     Vis:0.53
     Sum:250
3:10 4000
3:15 switching to WR140
     recording fringes at 500Hz/DEST/LONG
     Vis:0.27
     Sum:190
3:21 3960
     switching to cal 197037
3:22 recording fringes at 500Hz/DEST/LONG
     Vis:0.58
     Sum:120
3:27 switching to WR140
     recording fringes at 500Hz/DEST/LONG
     Vis:0.29
     Sum:220
3:33 3937
3:36 switching to cal 192985
     recording fringes at 500Hz/DEST/LONG
     Vis:0.47
     Sum:220
3:45 switching to WR140
     recording fringes at 500Hz/DEST/LONG
     Vis:0.27
     Sum:190
3:52 switching to HD 197037
     recording fringes at 500Hz/DEST/LONG
     Vis:0.52
     Sum:120

Re-attempting MWC342
offset 3700 on cal
- nothing

Attempting v1057Cyg and v1977Cyg : too faint in acquisition :-(

No other targets available in the list.


Summary
---------
3 brackets on v1295Aql
4 brackets on MWC340
could not find fringes on MWC342
could not lock on other north primary targets
3 brackets on WR140